User manual RYOBI EMS1122L SCHEMA 1

[. . . ] Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Ensure the switch is in the off-position before connecting to power source, picking up or carrying the tool. [. . . ] 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. SAFETY INSTRUCTIONS FOR RECIPROCATING SAWS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug RYOBI can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your RYOBI dealer Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with Keep hands away from cutting area and the blade; keep your second hand on barrel grip H 2 (if both hands are holding the saw, they can not be cut by the blade) Do not reach underneath the workpiece (the proximity of the blade to your hand is hidden from your sight) Never hold piece being cut in your hands or across your leg (it is important to support the work properly to minimise body exposure, blade binding, or loss of control) Use clamps or other equipment to secure and support the workpiece (holding the workpiece in your hand or against your body may lead to loss of control) Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord (contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator) Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Do not use a dull or damaged blade (bent blades can break easily or cause kickback) Keep hands away from between the tool housing and blade clamp D 2 (the blade clamp can pinch your fingers) Ensure that blade clamp D 2 is tight before making a cut (a loose clamp may cause the tool or blade to slip with loss of control as a result) Wear protective glasses and hearing protection 4 Use protective gloves when removing the blade from the tool (the saw blade may be hot after prolonged use) WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off 5 Speed control With wheel C 2 the sawing speed can be adjusted from low to high (6 positions) Adjusting sawing speed to material used 6 !if the tool does not run with wheel C 2 in position 1, select a higher sawing speed and lower the sawing speed while the tool runs Mounting saw blade 7 !disconnect the plug - press blade clamp D forward and hold it in that position - insert blade (with teeth facing down or up) to full depth 8 - release blade clamp D - pull out blade somewhat until clamp D clicks into a square position - push in and pull out blade to check whether it is locked correctly !ensure that blade clamp D 2 is tight before making a cut (a loose clamp may cause the tool or blade to slip with loss of control as a result) !ensure that the front end of the blade extends through footplate E for the entire stroke length Removing saw blade 8 - press blade clamp D forward and hold it in that position - pull out blade - release blade clamp D Adjustable footplate 9 - footplate E tilts in order to keep as much of its surface in contact with the workpiece - adjust footplate by holding the saw firmly and turning footplate to desired position Blade storage compartment 0 - ensure that storage compartment F is closed to prevent blades from falling out Operating the tool !securely clamp the workpiece - mark the cutting line on the workpiece - select desired sawing speed with wheel C 2 - connect plug to power source (light B turns on indicating that the tool is receiving power) !- hold the tool with one hand on handle G 2 and the other on the insulated barrel grip H 2 - switch on the tool !the tool should run at full speed before the blade enters the workpiece - guide the tool along the marked cutting line - keep footplate E 2 firmly against the workpiece to minimize counter-force and vibration Holding and guiding the tool !while working, always hold the tool at the greycoloured grip area(s) @ - keep ventilation slots J 2 uncovered - do not apply too much pressure on the tool; let the tool do the work for you !RUMOROSIT/VIBRAZIONE Misurato in conformit al EN 60 745 il livello di pressione acustica di questo utensile 89 dB(A) ed il livello di potenza acustica 100 dB(A) (deviazione standard: 3 dB), e la vibrazione 14, 6 m/s2 (metodo mano-braccio; incertezza K = 1, 5 m/s2). Fascicolo tecnico presso: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. H CE MINSGI TANUSITVANY Teljes felelssgnk tudatban kijelentjk, hogy jelen termk a kvetkez szabvnyoknak vagy ktelez hatsgi elrsoknak megfelel: EN 60 745, EN 55 014, a 2006/95/EK, 2004/108/EK, 98/37/EK (2009. 12. 28-ig), 2006/42/EK (2009. 12. 29-tOEl kezdve) elrsoknak megfelelen. ZAJ/REZGS Az EN 60 745 alapjn vgzett mrsek szerint ezen kszlk hangnyoms szintje 89 dB(A) a hangteljestmny szintje 100 dB(A) (norml eltrs: 3 dB), a rezgsszm 14, 6 m/s2 (kzre-hat rtk; szrs K = 1, 5 m/s2). A miszaki dokumentci a kvetkezOE helyen tallhat: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CZ CE STRVZUJC PROHLEN Potvrzujeme na odpovdnost, e tento vrobek odpovd nsledujcm normm nebo normativnm podkladm: EN 60 745, EN 55 014, podle ustanoven smrnic 2006/95/ES, 2004/108/ES, 98/37/ES (do 28. 12. 2009), 2006/42/ES (od 29. 12. 2009). HLUNOSTI/VIBRAC Meno podle EN 60 745 in tlak hlukov vlny tohoto pstroje 89 dB(A) a dvka hlunosti 100 dB(A) (standardn odchylka: 3 dB), a vibrac 14, 6 m/s2 (metoda ruka-pae; nepfiesnost K = 1, 5 m/s2). Technick dokumentace u: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. TR CE STANDARDIZASYON BEYANI Yeane sorumlu olarak, bu rnn aflaidaki standartlara veya standart belgelerine uygun olduunu beyan ederiz: EN 60 745, EN 55 014, ynetmelii hkmleri uyarinca 2006/95/EG, 2004/108/EG, 98/37/EG (28. 12. 2009 tarihine kadar), 2006/42/EG (29. 12. 2009 tarihinden itibaren). / GRLT/T<TREfiIM llen EN 60 745 gre ses basinci bu makinanin seviyesi 89 dB(A) ve al>flma s>ras>ndaki grlt 100 dB(A) (standart sapma: 3 dB), ve titreflim 14, 6 m/s2 (el-kol metodu; tolerans K = 1, 5 m/s2). Teknik belgelerin bulunduu merkez: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. PL OWIADCZENIE ZGODNOCI CE Niniejszym owiadczamy ponoszc osobist odpowiedzialno, e produkt wykonany jest zgodnie z nastpujcymi normami i dokumentami normalizujcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 2006/95/EU, 2004/108/EU, 98/37/EU (do 28. 12. 2009), 2006/42/EU (od 29. 12. 2009). HAASU/WIBRACJE Pomiarw dokonano zgodnie z norm EN 60 745 cinienie akustyczne narzdzia wynosi 89 dB(A) za poziom mocy akustycznej 100 dB(A) (poziom odchylenie: 3 dB), za wibracje 14, 6 m/s2 (metoda do-rka; bd pomiaru K = 1, 5 m/s2). Dokumentacja techniczna: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. RU , : EN 60 745, EN 55 014, 2006/95/EC, 2004/108/EC, 98/37/EC ( 28. 12. 2009), 2006/42/EC ( 29. 12. 2009). / co o EN 60 745 89 (A) e - 100 (A) ( : 3 dB), 14, 6 /2 ( ; K = 1, 5 /2). [. . . ] Sbor technickej dokumentcie sa nachdzaj na adrese: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. BG SK HR CE IZJAVA O USKLA ENOSTI Izjavljujemo uz punu odgovornost da je ovaj proizvod usklaen sa slijedeim normama i normativnim dokumentima: EN 60 745, EN 55 014, prema odredbama smjernica 2006/95/EG, 2004/108/EG, 98/37/EG (do 28. 12. 2009), 2006/42/EG (od 29. 12. 2009). BUCI/ VIBRACIJAMA Mjereno prema EN 60 745, prag zvunog tlaka ovog elektrinog alata iznosi 89 dB(A) a jakost zvuka 100 dB(A) (standardna devijacija: 3 dB), a vibracija 14, 6 m/s2 (postupkom na aci-ruci; nesigurnost K = 1, 5 m/s2). Tehnika dokumentacija se moe dobiti kod: RYOBI Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. SRB CE IZJAVA O USKLA ENOSTI Pod punom odgovornou izjavljujemo da je ovaj proizvod usklaen sa sledeim standardima ili standardizovanim dokumentima: EN 60 745, EN 55 014, u skladu sa odredbama smernica 2006/95/EG, 2004/108/EG, 98/37/EG (do 28. 12. 2009), 2006/42/EG (od 29. 12. 2009). BUKA/VIBRACIJE Mereno u skladu sa EN 60 745, nivo pritiska zvuka ovog alata iznosi 89 dB(A), a jaina zvuka 100 dB(A) (normalno odstupanje: 3 dB), a vibracija 14, 6 m/s2 (mereno metodom na aci-ruci; nesigurnost K = 1, 5 m/s2). [. . . ]