User manual RYOBI CHI1442

[. . . ] Moment of inattention while operating power tools may result in serious personal injury. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. [. . . ] Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injuries to person. To reduce risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage and stress. Use of improper extension cord could result in a risk of fire and electric shock. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. Do not disassemble charger; take it to a qualified serviceman when service or repair is required. To reduce risk of electric shock, unplug the charger from outlet before attempting any maintenance or cleaning. Refer to them frequently and use them to instruct others who may use this unit. 4V Chuck(mm) 2-13 Switch Variable speed No load speed(drill mode): -1 0-400 -Lo speed(min ) -Hi speed(min-1) 0-1400 No load speed(impact mode): -1 -Lo speed(min ) -Hi speed(min-1) Max Torque(Nm) 34 Battery pack BPP-1413/ BPP-1415/ BPP-1417 Charger BC-1440/ BC-1415-S Model CHP-1802 Voltage 18V Chuck(mm) 2-13 Switch Variable speed No load speed(drill mode): -Lo speed(min-1) 0-440 -Hi speed(min-1) 0-1600 No load speed(impact mode): -1 -Lo speed(min ) -Hi speed(min-1) Max Torque(Nm) 37 Battery pack BPP-1813/ BPP-1815/ BPP-1817 Charger BC-1800/ BC-1815-S CHI-1442 14. 4V 2-13 Variable speed 0-400 0-1400 0-5200 0-18200 34 BPP-1413/ BPP-1415/ BPP-1417 BC-1440/ BC-1415-S CHI-1802 18V 2-13 Variable speed 0-440 0-1600 0-5720 0-20800 37 BPP-1813/ BPP-1815/ BPP-1817 BC-1800/ BC-1815-S 14. Forward Reverse High speed Low speed Drive mode Drill mode (torque adjustment not active) Impact mode Chuck jaws Lock(tighten) Unlock (release) Drill bit(not included) Bit To decrease torque To increase torque Notch Ears Plate Depth stoprod clamp Auxiliary handle assembly Depth Gauge rod Drilling depth Battery Charger Green Light Red Light Keyless chuck Torque adjustment ring Switch trigger Gear train(High-Low) Quick mode selector Direction of rotation selector(forward/reverse/center lock) Bit storage area(s) Magnetic bit holder storage Magnetic tray Magnetic bit holder Battery pack Latches Depress latches to release battery pack 10 CHARGING YOUR BATTERY PACK The battery pack for your tool has been shipped in a low charge condition to prevent possible problems. Note: Batteries will not reach full charge the first time they are charged. Make sure power supply is normal house voltage, 230 volts, 50 Hz, AC only. The variable speed switch trigger delivers higher speed and torque with increased trigger pressure and lower speed with decreased trigger pressure. Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charger. When your battery pack becomes fully charged, the red light will turn off and the green light will turn on. After normal usage, 1 hour of charge time is required to be fully charged. [. . . ] If the torque is too high or the screws too small, the screws may be damaged or broken. The torque is greater when the torque adjustment ring is set on a higher setting. The torque is less when the torque adjustment ring is set on a lower setting. [. . . ]