User manual MCCULLOCH EUROMAC 390-38CC
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MCCULLOCH EUROMAC 390-38CC. We hope that this MCCULLOCH EUROMAC 390-38CC user guide will be useful to you.
Manual abstract: user guide MCCULLOCH EUROMAC 390-38CC
Detailed instructions for use are in the User's Guide.
[. . . ] Continual or regular users should therefore monitor closely the condition of their hands or fingers. The trimmer must be used exclusively as recommended (see section SAFETY USAGE). 4) Do not carry the trimmer while the engine is running even for short distances; switch off the engine and carry the unit with the cutting head behind you. when carrying the trimmer in a vehicle , secure it to avoid fuel leakage. [. . . ] The nylon string head also reduces the likelihood of damaging small plants and trees bark. Only use flexible, nonfilament nylon line in the nylon line head as specified by the manufacturer. Never use metallic line which could break off and become a dangerous projectile. When fitting or changing a cutting device, ensure you follow the instructions in the section "Blade or nylon string head assembly" with extreme precision. Fit these cutting devices using all and only the parts as described, and in the correct order. A blade with worn teeth besides providing poor performance might also generate a sudden thrust. 2) When using a saw tooth blade (optional accessory), the correct guard must be fitted (P/N 240553). Only use blades or nylon string heads clearly marked with a maximum speed of at least 10, 500 min-1. B: Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and therefore require the use of the appropriate size top flange to ensure a correct fit. Assemble the correct guard to suit the kind of blade or nylon string head to be used (See section: SAFETY GUARD ASSEMBLY). 1) Assemble blade as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Fixed mower gauge - f) Blade locking screw (length mm 16). 2) If you want to assemble the rotating mower gauge, proceed asillustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) 3) Make sure that the blade bore opening fits perfectly around the centering collar on the upper cap. While tightening, the blade assembly can be held fast by inserting the wrench or the screwdriver supplied into the cap and gearcase holes. 4) Assemble nylon string head as illustrated: a) Flange guard - b) Upper cap - c) Guard d) Nylon string head Tighten counterclockwise. 5) While tightening, the head assembly can be held fast by inserting the wrench or the screwdriver supplied into the holes as already shown for blade assembly. WARNING: Please do not use the accessory nylon string head guard (item C Fig. Make sure the shaft is fully and correctly engaged up to the shank, then tighten the 2 screws (A) in a criss-cross sequence. 2) Fit the end of the trigger cable connector (B) into the slot on swivel (C). 3) Adjust the screw (D) of the trigger cable connector so that the cable can easily slide in the opening with a play of 1 mm before operating the swivel (C). 2) DELTA FRONT HANDLE Secure the handle in front of the label placed on the shaft 11 cm from the rear grip when assembling nylon string head and 36 cm when assembling metallic blades. The handle bar must be mounted using all the items supplied and in the exact configuration shown in figures 1 or 2. 2) Depress the safety lever (S), squeeze the accelerator trigger (A) and push the throttle advance forwards (B). [. . . ] B: In order to extend the nylon line as it wears down, pull the mower gauge downwards and turn it in a clockwise direction to feed out the desired length of line. Engine will Engine runs badly or looses power not start when cutting Check STOP switch is in the position I. Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. The machine runs but does not cut well Engine still gives trouble: contact your dealer. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MCCULLOCH EUROMAC 390-38CC
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MCCULLOCH EUROMAC 390-38CC will begin.