User manual HUSQVARNA 560 SR

[. . . ] 560sr Owner’s Manual 532162421 02. 17. 98 REV. 1 VB Printed in U. S. A. SAFETY RULES Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROLS UNDER ANY CIRCUMSTANCES. TRAINING: • Read this operator’s manual carefully. [. . . ] Wet grass tends to form clumps and interferes with the mulching action. At this time the grass has dried and the newly cut area will not be exposed to the direct sun. For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn. • 1/3 MAX • FIG. 11 8 CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check for Loose Fasteners Clean/Inspect Grass Catcher (If Equipped) Clean Lawn Mower Clean Under Drive Cover (Power-Propelled Mowers) Check drive belt/pulleys (Power-Propelled Mowers) Check/Sharpen/Replace Blade Lubrication Chart Clean Battery/Recharge (Electric Start Mowers) Check Engine Oil Level Change Engine Oil Clean Air Filter Inspect Muffler Clean or Replace Spark Plug Replace Air Filter Paper Cartridge E E N US USE URS URS SO RAG H H O HO SEA TO C S EA AC 0 H 5 E R E Y 1 Y 2 ERY RE R E FO FT VER VER EV EFO SERVICE DATES E E OR B BE A M O W E R 3 4 E N G I N E 1, 2 2 2 1 - Change more often when operating under a heavy load or in high ambient temperatures. 4 - Charge 48 hours at end of season. GENERAL RECOMMENDATIONS The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • Once a year, replace the spark plug, clean or replace air filter element, and check blade for wear. A new spark plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer. Follow the Maintenance Schedule in this manual. LUBRICATION CHART 2 WHEEL ADJUSTERS 1 ENGINE 2 MULCHER DOOR • BEFORE EACH USE • • Check engine oil level. Check for loose fasteners. 2 HANDLE BRACKET MOUNTING PIN 2 REAR DOOR HINGE ROD LUBRICATION Keep unit well lubricated. IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. 1 REFER TO CUSTOMER RESPONSIBILITIES “ENGINE” SECTION 2 SPRAY LUBRICANT 9 CUSTOMER RESPONSIBILITIES LAWN MOWER Always observe safety rules when performing any maintenance. TIRES • • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. BLADE CARE For best results, mower blade must be kept sharp. • Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt. [. . . ] 532162716 532147715 873031000 532144929 532150327 532146315 532145212 532157008 532057079 532088446 532162399 812000058 532850017 532088080 532145354 532067725 DESCRIPTION Drive Control Drive Head Kit Nut, Metric Screw 1/4-20 V-Belt Screw Nut, Hex Flange Hubcap Washer Nylon Bushing Wheel & Tire Assembly E-Ring Pinion, L. H. 17 18 19 25 27 28 31 32 35 36 38 40 41 52 54 57 58 PART NO 532851980 532701037 532162715 532162868 532750097 532153822 532153823 532150326 532162420 532150330 532063601 532144902 532162419 532088614 532800386 532850016 532751152 DESCRIPTION Drive Pin Selector Knob Control Bar, Drive Upstop Bracket Screw #10-24 x 1/2 Bracket, Gearcase Lever, Clutch Drive Pulley Wheel Adjuster Assembly (Left) Gear Case Assembly Hex Locknut 1/4-20 Spring, Belt Tension Wheel Adjuster Assembly (Right) Catcher Frame Grassbag Assembly Pinion, R. H. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 532148145 532148123 532148118 532148135 532148122 532148132 532148093 532148114 532148095 532148109 532148102 532148112 532148108 532148112 532148095 532148096 532148103 532148101 532148097 532148090 532148097 532148083 532148097 532148075 532148097 532148113 532148119 532148121 532148098 532148115 532148111 532148110 DESCRIPTION Case, Lower Plate, Detent Support, Fork, Shift Ball, Detent Spring, Detent Support, Fork, Clutch Key, Woodruff Axle, Shaft Ring, 12. 7 Spring, Return Cone, Cave Washer, Thrust Bearing, Thrust, Needle Washer, Thrust Ring, 12. 7 Washer, Retainer Cone Collar, Shift Washer Gear, 3 Teeth Washer Gear, 3 Teeth Washer Gear, 3 Teeth Washer Ring 28 Spring, Shift Key, Shift Support, Key Collar, Shift Washer, Thrust 1/2 Bearing, Thrust, Needle KEY PART NO. NO. DESCRIPTION 20 33 532148111 Washer, Thrust 1/2 34 532148106 Bushing, Transmission 1/2 35 532148107 Seal 1/2 36 532148096 Washer, Retainer 37 532148104 Bushing, Transmission 38 532148107 Seal 1/2 39 532148116 Fork, Shift 40 532148124 Fork, Clutch 41 532148069 Bushing 42 532148065 Shaft, Reduction 43 532148066 Gear, Bevel 3 Teeth 44 532148089 Gear, Spur 2 Teeth 45 532148080 Gear, Spur 1 Tooth 46 532148072 Gear, Spur 1 Tooth 47 532148067 Washer 48 532148069 Bushing 49 532148141 Bearing, Ball 6000U 50 532148139 Washer, 10 51 532148140 Bearing, Ball 6200 52 532148137 Shaft, Input 53 532148146 Screw, Self-Tapping 54 532148144 Case, Upper 55 --Grease 56 532148142 Sealant 57 532148147 Screw, Self-Tapping, Case 58 532148117 Arm, Shift 59 532148127 Support, Upper, Clutch 60 532148138 Key, Woodruff 61 532148133 Pin, Snap 14 NOTE: All component dimensions given in U. S. [. . . ]