User manual FLECK 4600

[. . . ] System capacity Inlet water hardness Water hardness after mixing valve Brine tank size Quantity of salt per regeneration Standard piston CYCLE White Preliminary rinse Backwash Brine draw and slow rinse Rapid rinse Resin settling Brine refill X X X X X X Grey LWU piston Fast regen piston Blue Injector size Drain line flow control (DLFC) Brine line flow control (BLFC) GPM GPM Pressure regulator 1, 4 bar (20 PSI) Without 2, 1 bar (30 PSI) 230V/50Hz 24V/50-60Hz with transformer 24V/50-60Hz without transformer Valves complying european regulations: - Nr. Do not exceed 8, 5 bar; if you face this case, you should install a pressure regulator upstream the system. [. . . ] Use Teflon ® tape if necessary in order to seal between the drain fitting and the outlet flow control. Open a cold water tap nearby and let run a few minutes or until the system is free from foreign material (usually solder) that may have resulted from the installation. place the by-pass in service position and let water flow into the mineral tank. When water flow stops, slowly open a cold water tap nearby and let run until the air is purged from the unit. Initiate a manual regeneration, bring the valve into « brine draw and slow rinse position » in order to draw water from the brine tank until the blockage of the air check; the water level will be approximatively in the middle of the air check. Open a cold water tap and let the water run in order to drain the air out of the circuit. 24 hour wheel Program wheel in number of days between two regenerations Set the capacity of soft water between 2 regenerations using the following formula: Water capacity in m3 = exchange capacity in m3°tH ­ reserve capacity in m3 Water hardness °tH To do so, lift the transparent disc with the label and display the capacity facing the white dot. Use the same formula as for metered version and divide by daily water consumption to obtain the number of days between 2 regenerations. There are two time clock wheels: - 7 days: based on the week, number 1 will refer to Monday, number 7 to Sunday. Time of day Press the clutch on the 24 hour wheel, red gear, then turn the hour wheel to display the correct hour in the window. salt volume per regeneration Here is a table , usually used in water treatment. Salt weight n g / litre of resin 80 125 180 Exchange capacity in °tH / m3 / litre of resin 4 5 6 Salt weight in g / °tH / m3 20 25 30 This segment with an indicator ensures the function of brine refill. [. . . ] ): With this piston, water consumption during regeneration can be reduced. Injectorgrootte Drain line flow control (DLFC) Brine line flow control (BLFC) GPM GPM Regolatore di pressione 1, 4 bar (20 PSI) Zonder 2, 1 bar (30 PSI) Tape stripe 5600 timeclock std Front label 5600 timeclock with lamps Skipper wheel ring Idler shaft spring Ball 1/4" Skipper wheel 12 days assy Skipper wheel 7 days assy Regeneration pointer Screw Cycle actuator arm Wire nut European power cord Kit meter cable delayed 8 m3 Kit meter cable delayed 40 m3 Strain relief Main drive gear Microswitch assy for 5600 Brine cam assy (xx= salt weight label) Washer Screw Insulator Screw Serial number label Back cover assy 5600/4600 Screw Motor screw Motor 230V 50Hz 1/30 RPM Motor mounting plate Drive gear Idler gear Idler shaft spring Idler shaft Ball 1/4" Spring detent Motor pin Black drive housing Tape stripe 5600 Eco Std Front label 5600 Eco with lamps Red lamp 230V Green lamp 230V Label control knob Screw Control knob Valve dial position picto 5600/4600 Printed 24 hours gear Cycle actuator gear Program wheel assy 8 m3 Program wheel assy 40 m3 Out board bearing cap Screw End plug retainer Piston assembly standard Piston LWU assembly Piton Fast Regen assembly Seal & spacer kit New proportional mixing Valve body 5600 with mixing machining O'ring O'ring retainer O'ring top of tank 5600 valve O'ring top of tank 4600 valve Injector assembly 1600 for 5600 Injector assembly 4600 Air disperser Stand off (only 4600) Valve body 4600, brass Screw Meter cover assembly 8 m3 O'ring Impeller Meter body with o'ring O'ring Meter cover assembly 40 m3 Valve body Meter assembly only in volumetric Coupling adapter only in chronometric Plastic yoke adapter 1" male Plastic yoke adapter 3/4" male Brass yoke adapter 1" female Brass yoke adapter 3/4" male Bypass assembly 1" female [. . . ]