User manual DE DIETRICH DVH1084J

[. . . ] Do not connect the dishwasher until you have completed the installation. Connecting the power cable is the last step when installing the dishwasher. All wiring and grounding must be done in accordance with the electrical code applicable to the region. CAUTION _ safety instructions GROUNDING INSTRUCTIONS for a permanently connected appliance: This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Two or more people are needed to move a dishwasher and avoid potential injuries. [. . . ] If the dishwasher is installed in a corner, ensure that there is a clearance of more than 2 in. Cut a hole into the side of the wall where the sink is as shown in Figure 1 below. If there is an additional level in the sink cabinet and it is higher than the connections on the dishwasher, make two holes as shown in Figure 1-2. <figure 1-1> <figure 1-> The hole for the water supply line, drain hose and power cables. _ installing the dishwasher STep WATer SUPPly reqUIreMeNTS 1. The dishwasher can be connected to either the hot or the cold water supply. If the temperature of the water supplied to the dishwasher is below 149 °F (65 °C), connect it to the hot water supply. If it is higher than 149 °F (65 °C), connect it to the cold water supply. Ensure that the water supply valve is turned off before connecting the water supply line to the dishwasher. Seal the water supply line connections using teflon tape or sealing compound to stop any water leakage. The water supply line should be placed in the channels at the base of the dishwasher as shown in Figure 2. The drain hose connected to the dishwasher must be run through the hole in the side wall so it can be connected to the drain outlet of the sink. Place the dishwasher so that the water supply line and the power cable are located in the channels at the base of the dishwasher. Use standard duct tape to secure the water line and electrical cable to their adjacent channels in the base. Connect the water supply line into the elbow joint. CAUTION Do not place the dishwasher on the water supply line, drain hose or power cable. <figure > <figure > Drain hose power cable Water supply line Inlet valve Water supply line elbow 1_ installing the dishwasher STep levelING The dIShWASher 1. Open the door and place the level against the top of the tub from inside and check whether the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. 02 INSTAllING The dIShWASher . Check whether the dishwasher is upright (perpendicular), as shown in the figure to the right. . Open the door of the dishwasher and check whether both the tub and door clearances are correct. If not, rotate the leveling legs at the bottom front of the dishwasher. If the leveling legs are rotated to the left (counter clockwise), they are loosened and the front of the dishwasher is raised. If they are rotated to the right (clockwise), they are tightened and the front of the dishwasher is lowered. installing the dishwasher _1 installing the dishwasher STep SecUrING The dIShWASher The dishwasher should be fixed to the countertop or side walls for additional stability and safety. When the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in -1 below. [. . . ] (Each colored wire should be connected to its opposite wire of the same color. White should be connected to white, black to black, and green to green. ) . <figure 1> 02 INSTAllING The dIShWASher Black to black power cable Junction box White to white Green to green (Ground to ground) Strain relief <figure 1> installing the dishwasher _1 installing the dishwasher STep 11 cOMPleTING The INSTAllATION 1. Open the door and remove all foam, paper packaging and unnecessary parts. [. . . ]