User manual DE DIETRICH DTI701X

[. . . ] Good luck! 4 electrolux Contents Instructions for the User Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working?Service and original spare parts 5 7 8 10 12 22 Instructions for the Installer Engineers Technical Data Gas Connection Electrical Connection Adaptation to different Types of Gas Building In Possibilities for Insertion 13 16 17 18 19 21 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and Tips Environmental Information This appliance is manufactured according to the following EEC directives: 2006/95 EEC - 2004/108 EEC - 90/396 EEC, current edition. MANUFACTURER: ELECTROLUX ITALIA S. p. A. C. so Lino Zanussi, 30 ­ 33080 Porcia - PN (ITALY) electrolux 5 ENGLISH Important Safety Information These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. [. . . ] By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Description of the Hob 2 2 1 3 4 2 1. 5. Hob Top Semi-rapid Burner Triple Crown Burner Auxiliary Burner Control knobs for burners 5 8 electrolux INSTALLATION Any gas installation must be carried out by qualified personnel, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Operation The symbols mean: = no gas supply = maximum gas supply = minimum gas supply A B D Hob Burners To light a burner: Turn the relevant knob anticlockwise to maximum position and push down the knob to ignite. After lighting the flame, keep the knob pushed down for about 5 seconds. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. If you cannot light the flame even after several attempts, check the "cap" (Fig. In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob Fig. 1 Triple crown burner C A B D C A - Burner cap C B - Burner crown D - Ignition candle - Thermocouple electrolux 9 down and turn it anti-clockwise until it reaches the"maximum" position. Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (Fig. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. Periodic maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. 12 electrolux Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Electrolux Service Force Centre. SOLUTION Check that the unit is plugged in and the electrical supply is switched on. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. IMPORTANT - To ensure a correct operation, a saving of energy and the long life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection has to be fixed to the comprehensive ramp by means of a threaded nut G 1/2". Screw the parts without forcing, adjust the connection in the required direction and tighten everything. Connection using flexible non metal pipes When the connection can be easily inspected in its full extent, there is the chance to use a flexible pipe according to the rules in force. The flexible pipe must be tightly fixed using clamps according to the rules in force. The flexible pipe should be made ready for use in such a way that: - nowhere it can reach overtemperature, other than room temperature, higher than 30°C; - it is no longer than 1500 mm; - it shows no throttles; - it is not subject to traction or torsion; - it doesn't get in touch with cutting edges or corners; -it can be easily inspected in order to check its condition. The control of preservation of the flexible pipe consistsin checking that: - it doesn't show cracks, cuts, marks of burnings bothon D the end parts and on its full extent; - the material is not hardened, but shows its normal elasticity; - the fastening clamps are not rusted; A) Ramp with ending nut Fig. B) Seal If one or more abnormalities are seen, do not repair the C) Adjustable connection D) Rubber pipe holder for liquid gas pipe, but replace it. electrolux 17 It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. [. . . ] Hanging forniture units or hoods must be placed at 650 mm minimum from the hob. 51 Fig. 4 0 20 electrolux Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition candles are not damaged in this operation. [. . . ]