User manual DE DIETRICH DHD516XE1
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual DE DIETRICH DHD516XE1. We hope that this DE DIETRICH DHD516XE1 user guide will be useful to you.
You may also download the following manuals related to this product:
DE DIETRICH DHD516XE1 (618 ko)
DE DIETRICH DHD516XE1 (507 ko)
DE DIETRICH DHD516XE1 (2452 ko)
DE DIETRICH DHD516XE1 (361 ko)
DE DIETRICH DHD516XE1 (439 ko)
DE DIETRICH DHD516XE1 (359 ko)
DE DIETRICH DHD516XE1 (187 ko)
DE DIETRICH DHD516XE1 (175 ko)
DE DIETRICH DHD516XE1 (324 ko)
Manual abstract: user guide DE DIETRICH DHD516XE1
Detailed instructions for use are in the User's Guide.
[. . . ] The De dietrich range also includes a huge choice of fitted cooking hobs, ovens, dish-washers and refrigerators, that will match your new DE DIETRICH hood. Of course, we make every effort to ensure that our products meet all your requirements, and our Customer Relations department is at your disposal, to answer all your questions and to listen to all your suggestions (see back cover of manual). [. . . ] In particular, the evacuated air must not be channelled into a duct used to evacuate fumes from appliances using gas or other combustible fuels. Disused ducts may only be used after approval from a competent specialist. The minimum distance between the cooking surface and the lowest part of the hood must be 70 cm. If the instructions for the hob installed under the hood specify a distance of more than 70 cm, this requirement must be respected. - Draw a vertical line on the wall running from the ceiling to the lower edge of the hood. - Screw up the top two screws of the hood, but not completely - allow them to protrude by 5 mm. - Screw up the two screws at the bottom.
Adjust the level of your hood before fully tightening up all four screws.
Connecting up your hood
This appliance is delivered with a H 05 VVF power cable with three conductors of 0. 75 mm2 (neutral, live and earth). This must be connected to the 220-240 V single phase mains network via a CEI 60083 standard plug which must remain accessible following installation. We will not be liable in the event of an accident arising following incorrect or non-existent earthing. If the power cable is damaged, call the after sales service department in order to avoid danger.
Assembling the chimney
Hood to be used with external evacuation: fig. 4 and 8
- Attach the metal chimney bracket to the wall, also placing this against the ceiling (fig. - In the case of a flue with a diameter of 125 mm, use the adapter supplied (fig. If your exterior duct is below 125 mm, you must obligatorily connect your hood in recycling mode - Prepare your telescopic chimney taking care to block off the vents (fig. - Adjust the length of the telescopic chimney by bringing down the lower part and fitting it GB to the top of the hood.
To ensure optimal use of your device, we advise that you connect a flue with a diameter of 150 mm (not supplied). [. . . ] You should order these filters from your dealer (quoting the reference shown on the ID plate located inside the hood) and note the date the filter was changed.
WHY?
HOW ?
Never use metal scouring pads, abrasive products or excessively stiff brushes. To clean the body and the lighting port, you should use only commercial household cleaning products diluted in water and then rinse using clean water, drying with a soft cloth.
Dismantling the filter cartridge Fitting the carbon filter (fig. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE DE DIETRICH DHD516XE1
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual DE DIETRICH DHD516XE1 will begin.