User manual ASUS WL-520GU
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ASUS WL-520GU. We hope that this ASUS WL-520GU user guide will be useful to you.
You may also download the following manuals related to this product:
ASUS WL-520GU (6828 ko)
ASUS WL-520GU (2904 ko)
ASUS WL-520GU (3012 ko)
ASUS WL-520GU (3031 ko)
ASUS WL-520GU (3000 ko)
ASUS WL-520GU (2993 ko)
ASUS WL-520GU (3169 ko)
ASUS WL-520GU (2978 ko)
ASUS WL-520GU (6828 ko)
Manual abstract: user guide ASUS WL-520GU
Detailed instructions for use are in the User's Guide.
[. . . ] Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated. Follow steps 1-3 to install additional modules.
Memory socket Retaining clips
2
Install the CPU and heatsink with fan
Lever
1. Unlock the socket by pressing the level sideways, then lift it up to a 90º~100º angle. [. . . ] DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU. If the CPU does not fit, check its orientation or check for bent pins. When the CPU is in place, push down the socket lever to secure the CPU. (Refer to the documentation that came with the heatsink with fan and the motherboard user guide. ) 6. Connect the CPU fan power cable to the CPU fan connector on the motherboard.
Socket CPU
Small triangle
Gold triangle
Heatsink with fan
3
English
English
3
Mount the motherboard
Screws
NOTE: The following procedure applies to most standard chassis. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
1. Screw the standoffs that came with your chassis into the appropriate screw holes on the chassis. Remove the temporary metal shield on the rear panel that covers the rear I/O slot opening. Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The system may become unstable or may not boot up if the power is inadequate. 20-pin connector 4-pin connector
9
Connect the peripherals and accessories
Power strip PS/2 Mouse
AC
Keyboard
PS/2
Parallel
Printer
Digital Speakers
S/PDIF
IEEE 1394
Mobile HDD
PDA cradle
Serial
RJ-45
Switch Hub
Storage device
USB
Line in
Tape recorder
Microphone
Mic
VGA
CRT Monitor
Speakers
Line Out
DVI
Flat Panel Monitor
9
English
English
10
Power Up
Turn on the power of the monitor, peripherals and system. If necessary, format your hard disk drive and install an operating system. NOTE: If you encounter any BIOS related problems, enter the BIOS setup by pressing <Del> during startup. To restore all BIOS settings to the default value, press <F5> and select Yes.
Troubleshooting
If you encounter any of the following conditions when powering up the system, try performing one of the possible solutions before calling for technical support.
CONDITIONS
PC won't start up PC starts up, but no display
POSSIBLE SOLUTIONS
· Check the power cord and make sure it is connected properly. · Make sure that the monitor is turned ON and properly connected to the graphics port. · Check the brightness and contract controls of the monitor, make sure it is turned up. [. . . ] · Shutdown the computer, disconnect the power cord, and make sure the graphics card is inserted properly in its expansion slot. · Check the memory modules and make sure they are of the correct type. · Make sure that the memory modules are properly inserted into the sockets. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ASUS WL-520GU
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ASUS WL-520GU will begin.